LaboTex Program - The ADC Method References

ADC Method - the Basis of the LaboTex Software

The Texture Analysis Software - LaboTex - References

The LaboTex Reference:

K.Pawlik, P.Ozga: "LaboTex: The Texture Analysis Software",'Göttinger Arbeiten zur Geologie und Paläontologie', SB4, 1999.

The ADC Method - Main References:

K.Pawlik - phys.stat.sol.(b) 134 (1986), p.477, "Determination of the Orientation Distribution Function from Pole Figures in Arbitrarily Defined Cells" Abstract ,
K.Pawlik, J.Pospiech - Proc. of Int. Workshop, Clausthal-Zellerfeld, Germany, (1986), p127
K.Pawlik, J.Pospiech, K.Lucke - Proc. of ICOTOM-8, Santa Fe, USA, (1987), p105,"The Development of a New Direct Method of ODF Reproduction From Pole Figures and its Testing with the Help of Model Functions"
K.Pawlik, W.Truszkowski, J.Pospiech, T.Pawlik - Proc. of ICOTOM-8, Santa Fe , USA (1987), p531
K.Pawlik, J.Pospiech, K.Lucke - Proc. of ICOTOM-9, Avignon , France, (1990), p25, "The ODF approximation from pole figures with the aid of the ADC-method".
K.Pawlik - Proc. of EPDIC-2, Enschede, The Netherlands, (1992), p151
K.Pawlik - Proc. of ICOTOM-10, Clausthal-Zellerfeld, Germany, (1993), p401
H.R.Wenk, K Pawlik, J Pospiech and J.S Kallend - Deconvolution of superposed pole figures by discrete ODF methods: Comparison of ADC and WIMV for quartz and calcite with trigonal crystal and triclinic specimen symmetry - Textures and Microstructures 22 (1994), p233-260.
U.F.Kocks, C.N.Tome, H.R.Wenk, "Texture and Anisotropy", Cambridge University Press. (2000);

Others, Selected References on LaboTex and ADC Method:

"... The strong and weak points of each method are examined showing that the iterative discrete methods (ADC and WIMV) are better suited for the reproduction of the texture function in the present case. In comparing these two discrete methods, it is evidenced that the ADC method reproduces more accurately both the experimental and synthetic texture functions over the entire range of texture sharpness considered ..." F.Caleyo, T.Baudin, M.H.Mathon and R.Penelle - Comparison of several methods for the reproduction of the orientation distribution function from pole figures in medium to strong textured materials - Eur. Phys. J. AP 15 (2001), p85-96 Abstract
"... A discrete method (called as the Arbitrarily Defined Cells method) was applied to calculate the ODF. The 3-D distribution of orientations of the cellulose crystalline areas was reconstructed in the space of the Euler angles. Additionally, the complete pole figures as well as the inverse ones were recalculated. The presented analysis of the cellulose texture provides more extensive information on the space organisation of microfibrils than the standard methods...", Olek W., Pawlik K., Bonarski J. (2000): Space orientation of the crystalline areas of cellulose. Proceedings of the International Conference on Wood and Wood Fiber Composites, 13-15 April 2000, Stuttgart, Germany: 37-46.
"... Direct Methods (WIMV, ADC) With 1 Degree Resolution Are Preferred...", K.J.Kozaczek,D.S.Kurtz, Quantitative texture analysis of blanket films and interconnects, Workshop on Texture in Electronic Applications NIST, Gaithersburg, MD, October 10-11, 2000.
2011-2012
Jia, N.; Roters, F.; Eisenlohr, P.; Kords, C.; Raabe, D."Non-crystallographic shear banding in crystal plasticity FEM simulations: Example of texture evolution in ?-brass", Acta Materialia, 60,3 (2012) pp. 1099-1115.
Suresh, K.S.; Geetha, M.; Richard, C.; Landoulsi, J.; Ramasawmy, H.; Suwas, S.; Asokamani, R.,"Effect of equal channel angular extrusion on wear and corrosion behavior of the orthopedic Ti–13Nb–13Zr alloy in simulated body fluid "Materials Science & Engineering C, 32, 4, 1, (2012) pp. 763-771.
Roy, Shibayan; D., Satyaveer Singh; Suwas, Satyam; Kumar, S.; Chattopadhyay, K.,"Microstructure and texture evolution during accumulative roll bonding of aluminium alloy AA5086",Materials Science & Engineering A, 528, 29-30,15 (2011) pp. 8469-8478.
Gurao, N.P.; Sethuraman, S.; Suwas, Satyam,"Effect of strain path change on the evolution of texture and microstructure during rolling of copper and nickel", Materials Science & Engineering A, 528, 25-26, 25 (2011) pp. 7739-7750.
Rodriguez-Navarro, Alejandro B.; Checa, Antonio; Willinger, Marc-Georg; Bolmaro, Raúl; et. al.,"Crystallographic relationships in the crossed lamellar microstructure of the shell of the gastropod Conus marmoreus", Acta Biomaterialia, 8,2 (2012) pp. 830-835.
K.Lukaszkowicz, A.Czyzniewski,W.Kwasny,M.Pancielejko,"Structure and mechanical properties of PVD coatings deposited onto the X40CrMoV5-1 hot work tool steel substrate", Vacuum, 86, 8,29 (2012) pp. 1186-1194.
Li Jizhong, Xu Wei, Wu Xiaolin, Ding Hua, Xia Kenong,"Effects of grain size on compressive behaviour in ultrafine grained pure Mg processed by equal channel angular pressing at room temperature", Materials Science & Engineering A, 528, 18, 15, (2011), pp. 5993-5998.
B.C.De Cooman, Kim Jinkyung, Lee Seil,"Heterogeneous deformation in twinning-induced plasticity steel",Scripta Materialia, 66,12,(2012) pp. 986-991.
W.J.Kim,S.J.Yoo, H.T.Jeong, D.M.Kim,B.H.Choe,J.B.Lee,"Effect of the speed ratio on grain refinement and texture development in pure Ti during differential speed rolling",Scripta Materialia, 64,1,(2011) pp. 49-52.
Q.H,Bui, X.T.Pham,"Modeling of microstructure effects on the mechanical behavior of ultrafine-grained nickels processed by hot isostatic pressing",International Journal of Mechanical Sciences, 53, 10, (2011), pp. 812-826.
L.Li,"Deformation band and texture of a cast Mg–RE alloy under uniaxial hot compression", Materials Science & Engineering A, 528, 24, 15, (2011), pp. 7178-7185.
Biswas, Somjeet; Suwas, Satyam, "Evolution of sub-micron grain size and weak texture in magnesium alloy Mg–3Al–0.4Mn by a modified multi-axial forging process ", Scripta Materialia, 66, 2, (2012), pp. 89-92 .
C.Mondal, A.K.Singh,"Effect of change of rolling planes on orientation rotation around the ß-fiber of high-purity aluminum plate subjected to 90% cold pre-deformation",Scripta Materialia,66,9,(2012) pp. 674-677.
Yu.Ivanisenko, W.Skrotzki, R.Chulist,T.Lippmann,L.Kurmanaeva, ,,Texture development in a nanocrystalline Pd–Au alloy studied by synchrotron radiation", Scripta Materialia, 66,3-4,(2012),pp. 131-134
CG.Oertel, R.Schaarschuch,G.H.Cao,H.N.Tian,J.Freudenberger,H.G.Brokmeier, et. al,"Effect of martensitic phase transformation on the ductility of polycrystalline YCu", Scripta Materialia, 65, 9, (2011), pp. 779-782.
M.J.N.V.Prasad, A.H.Chokshi, Microstructural stability and superplasticity in an electrodeposited nanocrystalline Ni–P alloy, Acta Materialia Volume: 59, Issue: 10, June, 2011, pp. 4055-4067
Jia, N.; Peng, R. Lin; Wang, Y.D.; Zhao, X., Self-consistent modeling of rolling textures in an austenitic–ferritic duplex steel, Materials Science & Engineering A, 528, 10-11, 25 (2011), pp. 3615-3624
Biswas, Somjeet; Suwas, Satyam; Sikand, R.; Gupta, Anil K., Analysis of texture evolution in pure magnesium and the magnesium alloy AM30 during rod and tube extrusion, Materials Science & Engineering A Volume: 528, Issue: 10-11, April 25, 2011, pp. 3722-3729
Vignal, V.; Zhang, H.; Delrue, O.; Heintz, O.; Popa, I.; Peultier, J., Influence of long-term ageing in solution containing chloride ions on the passivity and the corrosion resistance of duplex stainless steels, Corrosion Science Volume: 53, Issue: 3, March, 2011, pp. 894-903
Khatirkar, Rajesh K.; Kumar, Sunil, Comparison of recrystallization textures in interstitial free and interstitial free high strength steels, Materials Chemistry and Physics Volume: 127, Issue: 1-2, May 16, 2011, pp. 128-136
Andasmas, M.; Langlois, P.; Fagnon, N.; Chauveau, Th.; Hendaoui, A.; Vrel, D. Phenomenological study of the densification behavior of Aluminum–Nickel powder mixtures during cold isostatic pressing and differential hydrostatic extrusion, Powder Technology Volume: 207, Issue: 1-3, February 15, 2011, pp. 304-310
Kim, W.J.; Yoo, S.J.; Jeong, H.T.; Kim, D.M.; Choe, B.H.; Lee, J.B., Effect of the speed ratio on grain refinement and texture development in pure Ti during differential speed rolling, Scripta Materialia Volume: 64, Issue: 1, January, 2011, pp. 49-52
V.D.Hiwarkar; S.K.Sahoo;, I. Samajdar; A.Satpathy; K.V.Krishna Mani; G.K.Dey; D.Srivastav; et. al., Defining recrystallization in pilgered Zircaloy-4: From preferred nucleation to growth inhibition, Journal of Nuclear Materials Volume: 412, Issue: 3, May 31, 2011, pp. 287-293
2005 - 2010
L. Tarkowski a, J. Bonarski, I. Alexandrov, Planar irregularities of texture and stress field in Ti detected by X-ray diffraction technique, Nuclear Instruments and Methods in Physics Research B 268 (2010) 352–355.
G. Dirras, H. Couque, J. Gubicza, A. Ouarem, T. Chauveau, P. Jenei, Fine-grained nickel deformed by direct impact at different velocities, Microstructure and mechanical properties, Materials Science and Engineering A 527 (2010) 4128–4135.
S.K. Sahoo, V.D. Hiwarkar, L. Jain, I. Samajdar, P. Pant, G.K. Dey, D. Srivastav R. Tewari, S. Banerjee, Deformed microstructures of two-phase Zr–2.5Nb alloy: Effects of the second phase hardness, Journal of Nuclear Materials 404 (2010) 222-230.
R. Chulist,W.Skrotzki,C.-G.Oertel,A.Bohm,T.Lippmann, E.Rybacki, Microstructure and texture in Ni50Mn29Ga21 deformed by high-pressure torsion, Scripta Materialia 62 (2010) 650–653.
J. Arout Chelvane, S. Banumathy, Mithun Palit, Himalay Basumatary, A.K. Singh, S. Pandian, Texture and magnetostriction studies in Bridgman solidified Ho0.85Tb0.15Fe1.95 alloys, Journal of Alloys and Compounds 507 (2010) 162–166.
Li Li, Xinming Zhang, Changping Tang, Yunlai Deng, Nan Zhou, Mechanical properties and deep drawability of Mg–Gd–Y–Zr alloy rolling sheet at elevated temperatures, Materials Science and Engineering A 527 (2010) 1266–1274.
R. Chulist,W. Skrotzki,C.-G. Oertel,A.Bohmb, M.Potschke, Change in microstructure during training of a Ni50Mn29Ga21 bicrystal, Scripta Materialia 63 (2010) 548–551.
R. Dakhlaoui,V. Klosek,M.H. Mathon,B. Marini, Orientation stress field analysis in polycrystalline bcc steel using neutron diffraction, Acta Materialia 58 (2010) 499–509.
Akinobu Shibata,Homuro Noda,Masato Sone,Yakichi Higo, Thin Solid Films 518 (2010) 5153–5158.
W.J. Kim, S.J. Yoo, H.T. Jeong, D.M. Kim, B.H. Choe and J.B. Lee, Effect of the speed ratio on grain refinement and texture development in pure Ti during differential speed rolling, Scripta Materialia 64 (2011) 49–52.
A. Chakraborty,M.Dutta,R.Pais,R.K.Ray,Analysis of an uncommon coating defect on industrial galvannealed high strength interstitial free steel, Surface & Coatings Technology 204 (2010) 3481–3489.
B. Ravi Kumar, S.K. Das, Sailaja Sharma, J.K. Sahu, Effect of thermal cycles on heavily cold deformed AISI 304L austenitic stainless steel, Materials Science and Engineering A 527 (2010) 875–882.
Karen Pantleon, Marcel A.J. Somers, Interpretation of microstructure evolution during self-annealing and thermal annealing of nanocrystalline electrodeposits—A comparative study, Materials Science and Engineering A 528 (2010) 65–71.
Nicole Stanford, Dale Atwell, Matthew R. Barnett, The effect of Gd on the recrystallisation, texture and deformation behaviour of magnesium-based alloys, Acta Materialia 58 (2010) 6773–6783.
M. Lederer V. Gröger, G. Khatibi, B. Weiss, Size dependency of mechanical properties of high purity aluminium foils, Materials Science and Engineering A 527 (2010) 590–599.
M.J.N.V. Prasad , A.H. Chokshi, Superplasticity in electrodeposited nanocrystalline nickel, Acta Materialia 58 (2010) 5724–5736.
Raghavendra R. Adharapurapu,Fengchun Jiang, John F. Bingert, Kenneth S. Vecchio, Influence of cold work and texture on the high-strain-rate response of Nitinol, Materials Science and Engineering A 527 (2010) 5255–5267.
Mario Birkholz, "Thin Film Analysis by X-Ray Scattering", Wiley VCH, ISBN:3527607048, 227,236.
Panicker, R.; Chokshi, A.H.; Mishra, R.K.; Verma, R.; Krajewski, P.E. "Microstructural evolution and grain boundary sliding in a superplastic magnesium AZ31 alloy"; Acta Materialia Volume: 57, Issue: 13 (2009) 3683-3693
Chakraborty, A.; Ray, R.K. "Influence of microstructure and texture on the formability character of industrially produced galvannealed coatings on three interstitial free steels"; Surface & Coatings Technology Volume: 203, Issue: 13 (2009) 1756-1764
Prasad, M.J.N.V.; Suwas, S.; Chokshi, A.H. "Microstructural evolution and mechanical characteristics in nanocrystalline nickel with a bimodal grain-size distribution" Materials Science & Engineering A Volume: 503, Issue: 1-2, (2009) 86-91.
Kim, W.J.; Yoo, S.J.; Chen, Z.H.; Jeong, H.T. "Grain size and texture control of Mg–3Al–1Zn alloy sheet using a combination of equal-channel angular rolling and high-speed-ratio differential speed-rolling processes"; Scripta Materialia Volume: 60, Issue: 10, (2009) 897-900
Gurao, Nilesh P.; Ali A, Ashkar; Suwas, Satyam, "Study of texture evolution in metastable ß-Ti alloy as a function of strain path and its effect on ? transformation texture"; Materials Science & Engineering A Volume: 504, Issue: 1-2, (2009) 24-35
Sahoo, S.K.; Hiwarkar, V.D.; Majumdar, A.; Samajdar, I.; Pant, P.; Dey, G.K.; Srivastav, D.; Tiwari, R.; et. al. "Presence and absence of significant twinning: Effects on cold deformed microstructures of single phase Zircaloy 2"; Materials Science & Engineering A Volume: 518, Issue: 1-2 (2009) 47-55.
Hiwarkar, V.D.; Sahoo, S.K.; Samajdar, I.; Narasimhan, K.; Mani Krishna, K.V.; Dey, G.K.; Srivastava, D.; et. al. "Annealing of cold worked two-phase Zr-2.5 Nb—Associated microstructural developments", Journal of Nuclear Materials Volume: 384, Issue: 1, (2009) 30-37.
Niranjani, V.L.; Hari Kumar, K.C.; Subramanya Sarma, V. "Development of high strength Al–Mg–Si AA6061 alloy through cold rolling and ageing" Materials Science & Engineering A Volume: 515, Issue: 1-2, (2009) 169-174.
W. Skrotzki, B. Kloden, A. Lankau, R. Chulist, V. Kopylov, H.-G. Brokmeier, "Texture lnhomogeneity in Titanium Deformed by ECAP", ARCHIVES OF METALLURGY, 53 (2008) 29-32.
Gravier, J.; Vignal, V.; Bissey-Breton, S.; Farre, J. "The use of linear regression methods and Pearson’s correlation matrix to identify mechanical–physical–chemical parameters controlling the micro-electrochemical behaviour of machined copper" Corrosion Science Volume: 50, Issue: 10, (2008) 2885-2894
B. J. Bonarski, B. Miku³owski. E. Schafler, Ch. Holzleithner, M. J. Zehetbauer, "Crystallographic Textures of Single and Polycrystalline pure Mg and Cu Subjected to HPT Deformation", ARCHIVES OF METALLURGY, 53 (2008) 117-123.
Li, H.; Yin, F.; Sawaguchi, T.; Ogawa, K.; Zhao, X.; Tsuzaki, K. "Texture evolution analysis of warm-rolled Fe–28Mn–6Si–5Cr shape memory alloy"; Materials Science & Engineering A Volume: 494, Issue: 1-2, (2008) 217-226
A. Góral, J. Jura, H. Paul, "On the Orientation Characteristics in Directionally Crystallized Al-CuAl2 Eutectic Alloy", ARCHIVES OF METALLURGY, 53 (2008) 139-143.
Yu, Z.M.; Odier, P.; Ortega, L.; Zhang, P.X.; Li, C.S.; Liu, X.H.; Zhou, L. "LZO covered Cu-based substrates"; Journal of Alloys and Compounds Volume: 460, Issue: 1-2 (2008) 519-523.
W. 0lek, J. Bonarski, "Texture Changes in Therminally Modified Wood" ARCHIVES OF METALLURGY, 53 (2008) 207-211.
Souza, C.M.; Abreu, H.F.G.; Tavares, S.S.M.; Rebello, J.M.A. "The ? phase formation in annealed UNS S31803 duplex stainless steel: Texture aspects" Materials Characterization Volume: 59, Issue: 9, (2008), 1301-1306.
V. Klosek, M.H. Mathon, M.H. Aouni, R. Chiron, V. Ji, "In situ analysis of deformation mechanisms of Cu-based fcc materials under uniaxial loading", Materials Science Forum, 571-572 (2008) 89-94.
Jiang, Z.Z.; Yu, S.H.; Chun, Y.B.; Shin, D.H.; Hwang, S.K., '"Grain refinement of pure vanadium by equal channel angular pressing", Materials Science & Engineering A, 479, 1-2 (2008) 285-292.
Jia, N.; Lin Peng, R.; Wang, Y.D.; Johansson, S.; Liaw, P.K. "Micromechanical behavior and texture evolution of duplex stainless steel studied by neutron diffraction and self-consistent modeling ", Acta Materialia Volume: 56, 4, (2008) 782-793.
Chun, Y.B.; Hwang, S.K., "Static recrystallization of warm-rolled pure Ti influenced by microstructural inhomogeneity", Acta Materialia 56, 3 (2008) 369-379.
Chakraborty, A.; Bhattacharjee, D.; Pais, R.; Ray, R.K., "Effect of galvannealing power on the texture and powdering resistance of industrially produced galvannealed coating on interstitial free steel", Scripta Materialia, 57, 8 (2007) 715-718.
Song, Jin-Hwa; Hong, Ki-Jung; Ha, Tae Kwon; Jeong, Hyo Tae, "The effect of hot rolling condition on the anisotropy of mechanical properties in Ti–6Al–4V alloy", Materials Science & Engineering A, 449-451, 25 (2007) 144-148.
Gabriel L. Converse, Weimin Yue, Ryan K. Roeder, "Processing and tensile properties of hydroxyapatite-whisker-reinforced polyetheretherketone", Biomaterials 28 (2007) 927-935. Abstract
S.B. Sadale, S.R. Barman, P.S. Patil, "Synthesis of type-II textured tungsten disulfide thin films with bismuth interfacial layer as a texture promoter", Thin Solid Films 515 (2007) 2935-2942.
Chowdhury SG, Datta S, Kumar BR, De PK, Ghosh RN, "Randomization of texture during recrystallization of austenite in a cold rolled metastable austenitic stainless steel", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 15 (2007) 114-119.
Jean-Marie Welter (Ed.),"Copper: Better Properties for Innovative Products", Wiley-VCH 2007. p.102.
Patro PK, Khatirkar R, Samajdar I, Kulkarni AR, Harendranath CS, "Strontium barium niobate-relating structural developments and dielectric constant", JOURNAL OF THE EUROPEAN CERAMIC SOCIETY 27 (5): (2007) 2255-2263.
Tom Walde, Hermann Riedel, "Simulation of earing during deep drawing of magnesium alloy AZ31", Acta Materialia 55 (2007) 867-874
S.B. Sadale, S.R. Barman, P.S. Patil, "Formation of _|_c texture of tungsten disulfide thin films with nickel", Applied Surface Science 253 (2007) 3489-3495.
W.J. Kim,J.B. Lee, W.Y. Kim,H.T. Jeongb and H.G. Jeongc, "Microstructure and mechanical properties of Mg-Al-Zn alloy sheets severely deformed by asymmetrical rolling", Scripta Materialia 56 (2007) 309-312.
B. Ravi Kumar, Mainak Ghosh "Surface and mid-plane texture evolution in austenite phase of cold rolled austenitic stainless steels",Materials Science and Engineering A 457 (2007) 236-245.
Cedric Chauvya, Pierre Barberis, Frank Montheillet, "Microstructure transformation during warm working of beta-treated lamellar Zircaloy-4 within the upper alpha-range", Materials Science and Engineering A 431 (2006) 59-67.
Chun, Y.B.; Semiatin, S.L.; Hwang, S.K. ''Monte Carlo modeling of microstructure evolution during the static recrystallization of cold-rolled, commercial-purity titanium'', Acta Materialia Volume: 54, Issue: 14, August, pp. 3673-3689, 2006.
Kouadri, A.; Barrallier, L. ''Texture characterisation of hexagonal metals: Magnesium AZ91 alloy, welded by laser processing'', Materials Science & Engineering A Volume: 429, Issue: 1-2, August 15, pp. 11-17, 2006.
Sadale, S.B.; Patil, P.S. ''Synthesis and characterization of type-II textured tungsten disulfide thin films by vdWR process with Pb interfacial layer as texture promoter'', Journal of Crystal Growth Volume: 290, Issue: 2, May 1, 2006, pp. 363-368.
Mani K.K.V.; Sain A.; Samajdar I.; Dey, G.K.; Srivastava, D.; Neogy, S.; Tewari, R.; Banerjee, S. ''Resistance to hydride formation in zirconium: An emerging possibility'', Acta Materialia Volume: 54, Issue: 18, October, pp. 4665-4675, 2006.
Souza J.C;Abreu,H.F.G;Teodósio,J.R, ''Comparação entre Diferentes Métodos de Cálculo da Função de Distribuição de Orientação Cristalográfica quando Aplicados em Aços Inoxidáveis Duplex'', III Workshop sobre Textura, Sao Paulo, 176-184,2006, ( On Line Access )
I.V. Alexandrov, M.V.Zhilina, J.T. Bonarski,"Formation of texture inhomogeneity in severely plastically deformed copper", Bulletin of the Polish Academy of Sciences, Technical Sciences, Vol. 54, No 2, 2006 ( On Line Access )
S.G.Chowdhury, E.V.Pereloma, D.B.Santos,''Evolution of Texture at the Initial Stages of Continuous Annealing of Cold Rolled Dual-Phase Steel, independent of Heating Rate'', ( On Line Access )
Chauvy C.; Barberis P.; Montheillet F,, ''Microstructure transformation during warm working of beta-treated lamellar Zircaloy-4 within the upper alpha-range'', Materials Science & Engineering A Volume: 431, Issue: 1-2, September 15, pp. 59-67, 2006.
Kumar, B. R.; Singh, A.K.; Mahato, B.; De, P.K.; Bandyopadhyay, N.R.; Bhattacharya, D.K. ''Deformation-induced transformation textures in metastable austenitic stainless steel'', Materials Science & Engineering A Volume: 429, Issue: 1-2, August 15, pp. 205-211, 2006.
Chowdhury SG, Das S, Ravikumar B, ''Twinning-induced sluggish evolution of texture during recrystallization in AISI 316L stainless steel after cold rolling'', METALL MATER TRANS A 37A (8): pp. 2349-2359 AUG 2006.
Chowdhury SG, Dutta A, Ravikumar B. Kumar A, ''Textural evolution during accumulative roll bonding of an Al-Li alloy'', MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 428 (1-2): 351-357 JUL 25 2006.
Pantleon K.; Somers M.A.J.,"X-ray diffraction investigation of self-annealing in nanocrystalline copper electrodeposits", SCRIPTA MATERIALIA, 55 (4): pp. 283-286, 2006.
Etter AL, Baudin T, Mathon MH, Swiatnicki W, Penelle R,"Stored energy evolution in both phases of a duplex steel as a function of cold rolling reduction",SCRIPTA MATERIALIA, 54 (4): 683-688 FEB 2006.
Etter AL, Baudin T, Rey C, Penelle R, "Microstructural and textural characterization of copper processed by ECAE", MATERIALS CHARACTERIZATION 56 (1): 19-25 JAN 2006,
Chowdhury, Sandip Ghosh; Srivastava, V.C.; Ravikumar, B.; Soren, S. "Evolution of texture during accumulative roll bonding (ARB) and its comparison with normal cold rolled aluminium–manganese alloy",Scripta Materialia Vol: 54, Issue: 9, May, 2006, pp. 1691-1696.
Bonarski JT, Olek W, ''Crystallographic texture changes of wood due to air parameter variations'', Z KRISTALLOGR : 607-612 Part 2 Suppl. 23 2006.
Bonarski J, Olek W, "Texture function application for wood ultrastructure description. Part 1: Theory", WOOD SCI TECHNOL 40 (2): 159-171 FEB 2006
Goral A, Jura J, Bouzy E, Sztwiertnia K, Morgiel J, Bonarski J, ''Multiscale texture and orientation relationship investigation in Al-CuAl2 eutectic alloy'', ARCHIVES OF METALLURGY AND MATERIALS 51 (1): 11-14 2006.
Bonarski, Jan T.,"X-ray texture tomography of near-surface areas", Progress in Materials Science Volume: 51, Issue: 1, January, 2006, pp. 61-149
1995 - 2005
E.Zschech, M.A.Meyer,I.Zienert, E.Langer, H.Geisler, A.Preusse, P.Huebler, "Electromigration-induced copper interconnect degradation and failure: the role of microstructure", Physical and Failure Analysis of Integrated Circuits, 2005. IPFA 2005. Proceedings of the 12th International Symposium on the Physical & Failure Analysis of Integrated Circuits , pp 85- 91.
Yu SH, Chun YB, Cao WQ, Kim MH, Chae SW, Kwun SI, Shin DH, Hwang SK,"Comparison of equal channel angular pressing and cold rolling in the evolution of microstructure and texture in zirconium",METALS AND MATERIALS INTERNATIONAL 11 (2): 101-111 APR 2005,
Chun YB, Yu SH, Semiatin SL, Hwang SK,"Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium",MATERIALS SCIENCE AND ENGINEERING A. 398 (1-2): 209-219 MAY 25 2005,
Yu SH, Chun YB, Hwang SK, Shin DH, "Texture development and Monte-Carlo simulation of microstructure evolution in pure Zr grain-refined by equal channel angular pressing",PHILOSOPHICAL MAGAZINE, 85 (2-3): 345-371 Sp. Iss. SI JAN 11 2005,
Kim SH, You BS, Yim CD, Seo YM, "Texture and microstructure changes in asymmetrically hot rolled AZ31 magnesium alloy sheets", MATERIALS LETTERS, 59 (29-30), (2005),3876-3880.
Blicharski M, Jura J, Baudin T, Penelle R, Bonarski J, Kowalski M, "Development of the orientation relationship between ferritic and austenitic phases during long time annealing of duplex stainless steel" ARCHIVES OF METALLURGY AND MATERIALS, 50 (2): 495-502, SI 2005
R.Kumar, B.Mahato, N.R.Bandyopadhyay, D.K.Bhattacharya,"Comparison of rolling texture in low and medium stacking fault energy austenitic stainless steels", Materials Science & Engineering A, Vol: 394, Issue: 1-2, March 15, 2005.
Y.B.Chun,S.H.Yu, S.L.Semiatin, S.K.Hwang,"Effect of deformation twinning on microstructure and texture evolution during cold rolling of CP-titanium", Materials Science & Engineering A Vol: 398, Issue: 1-2, May 25, 2005.
Alexandrov IV, Zhilina MV, Scherbakov AV, Korshunov AI, Nizovtsev PN, Smolyakov AA, Solovyev VP, Beyerlein IJ,"Texture formation during severe plastic deformation",MATERIALS SCIENCE FORUM,495-497: 785-790 Part 1&2 2005,
M.V.Z. Zhilina, I.V. Alexandrov,J.T. Bonarski,A.V.Scherbakov,"Analysis of homogeneity of texture formation processes under high pressure torsion", ,E-MRS Fall Meeting 2005, Symposium I.
Kusnierz J, Bogucka J.,"Evolution of texture during ARB processing of Al 99.8%",MATERIALS SCIENCE FORUM, 495-497: 797-802 Part 1&2 2005,
S.H.Yu, Y.B.Chun,S.K.Hwang,D.H.Shin,"Texture development and Monte-Carlo simulation of microstructure evolution in pure Zr grain-refined by equal channel angular pressing", Philosophical Magazine, Volume 85, Numbers 2-3, 11 January-21 January 2005.
Vogel SC, Hartig C, Von Dreele RB, Wenk HR, Williams DJ,"Quantitative texture measurements using neutron time-of-flight diffraction",MATERIALS SCIENCE FORUM, 495-497: 107-112 Part 1&2 2005,
Tarkowski L., Bonarski J., W.D¹browski "Application of the Si-strip detector in X-ray crystallographic texture measurements", Nuclear Inst. and Methods in Physics Research, A Volume: 551, Issue: 1, October 1, 2005, pp. 178-182.
Zhilina MV, Bonarski J, Scherbakov AV, Alexandrov IV, Makarychev K, "Analysis of texture formation homogeneity processes during equal-channel angular pressing", ARCHIVES OF METALLURGY AND MATERIALS 50 (2), 479-485 SI 2005.
Mizera J, Pakiela Z, Kurzydlowski KJ,"Texture and residual stresses in Ti-Al and Ti-Al-Nb alloy subjected to severe plastic deformation", ARCHIVES OF METALLURGY AND MATERIALS, 50 (2), 395-402, SI 2005.
Espinoza Orias A.A.,"THE RELATIONSHIP BETWEEN THE MECHANICAL ANISOTROPY OF HUMAN CORTICAL BONE TISSUE AND ITS MICROSTRUCTURE", Thesis, University of Notre Dame, 2005.
Kusnierz J,"Rolling texture of ECAP processed Al and Cu",TEXTURE AND ANISOTROPY OF POLYCRYSTALS II, SOLID STATE PHENOMENA, 105: 339-344 2005,
T.Walde, H.Riedel, ''Modeling Texture Evolution during Rolling of Magnesium Alloy AZ31'', Solid State Phenomena, 105, 285-290, 2005.
Kusnierz J, Bogucka J.,"Accumulative roll-bonding (ARB) of A199.8%",ARCHIVES OF METALLURGY AND MATERIALS", 50 (1): 219-230 2005,
Ischia G, Wenk HR, Lutterotti L, Berberich F, "Quantitative Rietveld texture analysis of zirconium from single synchrotron diffraction images", JOURNAL OF APPLIED CRYSTALLOGRAPHY, 38: 377-380 (2) 2005.
Chateigner D, "Reliability criteria in quantitative texture analysis with experimental and simulated orientation distributions",JOURNAL OF APPLIED CRYSTALLOGRAPHY, 38: 603-611 Part 4 AUG 2005
Kapoor K.,Lahiri D.,Rao S.V.R., Sanyal T.,Saibaba N.,Kashyap B.P.,"Texture evolution in two phase Zr – 2.5 wt-%Nb through modified route",Materials Science and Technology, October 2004, vol. 20, no. 10, pp. 1281-1289(9).
Sarma, V. Subramanya; Eickemeyer, J.; Mickel, C.; Schultz, L.; Holzapfel, B., "On the cold rolling textures in some fcc Ni-W alloys" MATERIALS SCIENCE AND ENGINERING: A Volume: 380, Issue: 1-2, August 25, 2004, pp. 30-33
J.L.Jones,S.C.Vogel,E.B.Slamovich, K.J.Bowman,"Quantifying texture in ferroelectric bismuth titanate ceramics", Scripta Materialia, Vol: 51, Issue: 12, December, 2004
Jones JL, Slamovich EB, Bowman KJ, "Critical evaluation of the Lotgering degree of orientation texture indicator",JOURNAL OF MATERIALS RESEARCH, 19 (11): 3414-3422 NOV 2004,
Wenk HR, Lonardelli I, Williams D, "Texture changes in the hcp -> bcc -> hcp transformation of zirconium studied in situ by neutron diffraction",ACTA MATERIALIA, 52 (7): 1899-1907, 2004
Jones JL, Vogel SC, Slamovich EB, Bowman KJ, "Quantifying texture in ferroelectric bismuth titanate ceramics",SCRIPTA MATERIALIA, 51 (12): 1123-1127 DEC 2004,
Liu JT, Morris JG, "Recrystallization microstructures and textures in AA 5052 continuous cast and direct chill cast aluminum alloy", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 385 (1-2): 342-351, 2004
Wenk HR,"The Textures of Rocks in the Earth's Deep Interior: Part I. Understanding Anisotropy and Textures in Earth Materials", Encyclopedia of Materials: Science and Technology, Elsevier (2004);
Li HL, Glavicic MG, Szpunar JA, "A model of texture formation in ZrO2 films", MATERIALS SCIENCE AND ENGINEERING A, 366 (1): 164-174 FEB 5 2004,
Wenk HR, Lutterotti L, Vogel S, "Texture analysis with the new HIPPO TOF diffractometer",NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT 515 (2003) 575-588;
Anderson PM, Bingert JF, Misra A, Hirth JP,"Rolling textures in nanoscale Cu/Nb multilayers",ACTA MATERIALIA 51 (2003) 6059-6075;
Hayakawa Y, Kurosawa M.,"Orientation relationship between primary and secondary recrystallized texture in electrical steel", ACTA MATERIALIA 50 (18): 4527-4534 OCT 28 2002
Liu JT, Morris JG,"Macro-, micro- and mesotexture evolutions of continuous cast and direct chill cast AA 3105 aluminum alloy during cold rolling", MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 357 (2003) 277-296;
Liu JT, Morris JG,"Texture and grain-boundary evolutions and direct chill cast AA 5052 aluminum alloy during cold rolling",METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE 34A (2003) 951-966;
Liu JT, Morris JG, "Recrystallization textures of continuous cast AA 3015 alloy: Development of the P orientation {011}< 566 >", METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE 34A (2003) 2029-2032;
Kusnierz J, Bogucka J.,"Effect of ECAP processing on the properties of cold rolled copper",ARCHIVES OF METALLURGY, 48 (2): 173-182 2003,
Kusnierz J, Baudin T, Jasienski Z, Penelle R., "Neutron and X-ray diffraction study of Al and Cu during ECA processing C and subsequent recrystallization",REVUE DE METALLURGIE-CAHIERS D INFORMATIONS TECHNIQUES, 100 (9): 825-833 SEP 2003,
Etter AL, Mathon MH, Baudin T, Penelle R., "Stored energy evolution as a function of cold rolling reduction for a Fe-53%Ni alloy and an austenitic-ferritic steel",REVUE DE METALLURGIE-CAHIERS D INFORMATIONS TECHNIQUES, 100 (9): 851-858 SEP 2003,
Bechade JL, Mathon MH, Branger V, Regle H, Alamo A., "Texture analysis of oxide dispersion strengthened (ODS) Fe alloys by X-ray and neutron diffraction", JOURNAL DE PHYSIQUE IV 12 (PR6): 155-163 JUL 2002,
Kusnierz J, Kurowski M., "Strain softening enects in texture and microstructure of torsioned pre-deformed Al rods",ZEITSCHRIFT FUR METALLKUNDE, 93 (12): 1233-1236 DEC 2002,
Etter AL, Mathon MH, Baudin T, Penelle R., "A method of determination of stored energy in single and dual phase cold rolled materials", TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 583-588 2002
Kusnierz J, Kurowski M, Mathon MH, Baudin T, Jasienski Z, Penelle R.,"Effect of deformation path on torsion texture and stored energy of copper rods",TEXTURES OF MATERIALS, PTS 1 AND 2 MATERIALS SCIENCE FORUM, 408-4: 625-630 2002,
Kusnierz J, Mathon MH, Baudin T, Jasienski Z, Penelle R., "Neutron diffraction study of texture and stored energy in ECA pressed copper",TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 703-708 2002,
Kim BK, Szpunar JA, Varano R.,"Texture evolution in grain growth of nanocrystalline Ni",TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 937-942 2002
Kim BK, Szpunar JA, Zhilyaev AP., "Annealing texture in thermal stability of ultrafine-grained Ni",TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 943-948 2002,
Jura J, Baudin T, Mathon MH, Swiatnicki W, Penelle R., "Microstructure and texture analysis in a cold-rolled austenitic-ferritic steel with duplex structure",TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 1359-1364 2002
Caleyo F, Baudin T, Penelle R, "Study of the development of the cube texture in Fe-50%Ni during recrystallization and normal grain growth", EUROPEAN PHYSICAL JOURNAL-APPLIED PHYSICS 20 (2002) 77-89;
Park JY, Szpunar JA, "Influence of the primary recrystallization texture on abnormal grain growth of goss grains in grain oriented electrical steels",TEXTURES OF MATERIALS, PTS 1 AND 2, MATERIALS SCIENCE FORUM, 408-4: 821-826 2002,
Park JY, Han KS, Woo JS, Chang SK, Rajmohan N, Szpunar JA,"Influence of primary annealing condition on texture development in grain oriented electrical steels",ACTA MATERIALIA, 50 (7): 1825-1834 APR 19 2002,
Etter AL, Mathon MH, Baudin T, Branger V, Penelle R.,"Influence of the cold rolled reduction on the stored energy and the recrystallization texture in a Fe-53%Ni alloy", SCRIPTA MATERIALIA, 46 (4): 311-317 FEB 28 2002,
Kusnierz J., "Microstructure and texture evolving under Equal Channel Angular (ECA) processing",ARCHIVES OF METALLURGY, 46 (4): 375-384 2001.
Starczewski L, Bonarski JT; "Stress-textural indicators of tribological wear"; MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING 288 (2000) 284-287;
Bonarski JT, Wrobel M, Pawlik K,"Quantitative phase analysis of duplex stainless steel using incomplete pole figures", MATERIALS SCIENCE AND TECHNOLOGY, 16 (2000) 657-662;
Okuda K, Sakata K, Eloot K, Furukimi O, Obara T, "Mechanism of strong formation of {111} recrystallization texture of cold rolled IF steel sheet with {111} hot band texture", TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN 85 (8): 633-638 AUG 1999,
Pawlowski A, Bonarski J,"Plastic deformation in Ti-46at.%Al alloy of cellular-lamellar structure",44 (1999) 267-278;
Nowak R, Yoshida F, Morgiel J, Major B,"Postdeposition relaxation of internal stress in sputter-grown thin films caused by ion bombardment",JOURNAL OF APPLIED PHYSICS, 85 (1999) 841-852;
Bonarski J, Pawlik K,"Development of texture determination method for the near-surface-layers",ARCHIVES OF METALLURGY, 43 (1998) 141-148;
Komatsubara M, Hayakawa Y, Takamiya T, Muraki M, Maeda C, Ishida M, Morito N,"Newly developed grain-oriented Si-steel with thinner gauges", JOURNAL DE PHYSIQUE IV, 8 (1998) 467-474;
Eloot K, Okuda K, Sakata K, Obara T,"Texture evolution during cold rolling and recrystallisation of IF steel with a strong {111} hot band texture";ISIJ INTERNATIONAL, 38 (1998) 602-609;
Tarasiuk J, Wierzbanowski K, Baczmanski A,"New algorithm for the ODF calculation from pole figures",TEXTURE AND ANISOTROPY OF POLYCRYSTALS MATERIALS SCIENCE FORUM, 273-2 (1998) 133-138;
Dutkiewicz J, Bonarski J,"Structure, texture and mechanical properties of AlZnMgCuZr alloy rolled after heat treatments",MATERIALS & DESIGN, 8 (4-6) (1997) 247-252;
Hayakawa Y, Szpunar JA, "A comprehensive model of recrystallization for interstitial free steel",ACTA MATERIALIA 45 (1997) 3721-3730;
Hayakawa Y, Szpunar JA,"Modeling of texture development during recrystallization of interstitial free steel",ACTA MATERIALIA 45 (1997) 2425-2434;
Rajmohan N, Hayakawa Y, Szpunar JA, Root JH,"Neutron diffraction method for stored energy measurement in interstitial free steel",ACTA MATERIALIA 45 (1997) 2485-2494;
Hayakawa Y, Szpunar JA,"The role of grain boundary character distribution in secondary recrystallization of electrical steels",ACTA MATERIALIA 45 (1997) 1285-1295;
Matthies S, Lutterotti L, Wenk HR, "Advances in texture analysis from diffraction spectra",JOURNAL OF APPLIED CRYSTALLOGRAPHY, 30: 31-42 Part 1 (1997);
Akdut N, Foct J, Gottstein G, "Cold rolling texture development of alpha/gamma duplex stainless steels",STEEL RESEARCH 67 (10) (1996) 450-455.
N.Akdut,J.Foct, "Phase Boundaries and Deformation in High Nitrogen Duplex Stainless Steels I. - Rolling Texture Development", Scripta Metallurgica et Materiala, Vol: 32, Issue: 1, January 1, 1995
N.Akdut,J.Foct, "Phase Boundaries and Deformation in High Nitrogen Duplex Stainless Steels II. - Analysis of Deformation Mechanisms by Texture Measurements in X2 CrNiMo 22 5 (1.4462) Scripta Metallurgica et Materiala, Vol: 32, Issue: 1, January 1, 1995.
Texture Modelling: Co-operation of LaboTex with VPSC , M.Zylina, A.Schrbakov,I.V.Alexandrov,"Computer Modelling of Processes of Texture Development in Pure Copper During Equal Channel Angular Pressing",

Blogs:

Blog about ODF, LaboTex and more (in Japanese)

The ODF Transformation - references:

Adam Morawiec, Orientations and Rotations (2003), Springer, ISBN 3-540-40734-0.

The Calculation of the Volume Fraction of Texture Components. The ODF Modelling - references :

Determination of Volume Fraction of Texture Components Using LaboTex - Integration Method (manual) - www.labotex.com
Determination of Volume Fraction of Texture Components Using LaboTex - Model Functions Method (manual) - www.labotex.com
Determination of Volume Fraction of Texture Components Using LaboTex - Modelling of ODF, pole figures and inverse pole figures (manual) - www.labotex.com
J.W.Flowers, "Volume Fractions of Texture Components of Cubic Materials",
Textures and Microstructures, 1983, Vol.5, pp. 205-218,"A method for obtaining volume fractions in regions about ideal texture components of cubic materials by integration of the orientation distribution function is described".
J.H. CHO, A.D. ROLLETT, K.H. OH, "Determination of Volume Fractions of Texture Componentswith Standard Distributions in Euler Space", METALLURGICAL AND MATERIALS TRANSACTIONS A, VOLUME 35A, MARCH 2004—1075.
J. Kozaczek, D. S. Kurtz, P.R. Moran, R. Martin, M. E. Gross, K. Evans-Lutterodt, "Methodology of Quantitative Texture Analysis in Thin Films and Interconnects", http://www.hypernex.com/news/pdfs/2000AdvMetfinal.PDF
J.Jura, "Application of Model Function in Quantitative Texture Analysis of Cubic Metals", Metallurgy and Foundry Practice, Bulletin 148, No.1530,(1993).
S.Matthies, G.W.Vinel,K.Helming,"Standard Distribution in Texture Analysis, Akademie-Verlag Berlin (1987,1988,1991).

The Measurement of Pole Figures - references:

"Pole Figures: Registration and Plot Conventions" - www.labotex.com
B.D. Cullity,B. D. "Elements of X-ray Diffraction", Addison-Wesley, Reading, Mass (new edition p. 402-431 Pole Figures),
H.P. Klug, L.E.Alexander, "X-Ray Diffraction Procedures", John Wiley & Sons",
Schulz L.G.; (1949). J.Appl. Phys., 20, 1033,
D. Chateigner, P. Germi, M. Pernet: Texture analysis by the Schulz reflection method: defocusing corrections for thin films. J. of Applied Crystallography 25, 1992, 766-769

The Texture and Quantitative Phase Analysis - reference:

Bonarski J.T., Wróbel M. and Pawlik K.; (2000). Quantitative phase analysis of duplex stainless steel using incomplete pole figures, Materials Science and Technology Vol. 16 No 6, p. 657-662.

The Texture and ODF - references:

H.J. Bunge, "Texture analysis in materials science". Cuvillier Verlag, Göttingen;
U.F.Kocks, C.N.Tome,H.R.Wenk, "Texture and Anisotropy", Cambridge University Press. (2000),

Others ODF/Pole Figures Resources: